Better Pack
®555
On Line Service Guide
Since 1983
13093 Old Ridge Road Beaverdam Virginia 23015
1-800-899-9389
quality products - superior customer support
Power On - No Tape Dispensing
|
listing of electric & manual machines |
on line parts guide for Better Pack® Phoenix NPS |
on line service guides for Better Pack® Phoenix |
|
|
|
|
|
|
< back to Better Pack 555 ®Trouble Shooting Guide Start Page
Better Packages 555 ®Service Guide Links
|
|
|
|
|
|
|
|
|
|
|
|
POWER ON - NO TAPE DISPENSING
The most common cause is a defective or improperly adjusted Safety Switch -400SafetySwitch (Ref FF112). Turn on the tape machine. If the pilot light is on and the Top Heater is heating, yet none of the key switches will dispense tape, the probable cause is the Safety Switch.
Quick Safety Switch Check
Here's a quick way to check the Safety Switch. Unplug the machine. Remove the Key Drum & Access Hole Cover. The Safety Switch is located towards the front of the large Measuring Wheel (see Service Figures 10 & 11 below).
First, check the wires and make sure they are connected to the Safety Switch!
On 555 S Models: Service Figure 10
The Switch Trip Lever - 400TripLever (Ref EA82B) shuts the safety switch off. Check this lever. Make sure it is not broken. Check the spring 400LeverSpring (Ref EA80) to make sure it is not broken. If the lever is bent up or broken or the spring is broken, replace them. Next, check to make sure the Safety Switch is shut off. Push the small white button on the top of the switch down. Try plugging the machine back in and see if it operates. If it does, the problem was that the Safety Switch did not shut back off. You may need to replace either the lever or spring. If the white button was down, or pushing it down does not reset the machine, you may need to replace the Safety Switch (see below)
On 555 L Models: Service Figure 11
The Safety Switch is screwed into the Safety Switch Bracket on the side frame. When the Bumper Cup Arm returns to home position, it has to push up the copper Safety Switch Spring to reset the switch. Check to make sure this lever is operating properly. If it is broken, you can order just the Safety Switch Bracket .
IF THE SPRING IS NOT BROKEN TRY THIS -
Rotate the Measuring Wheel by hand and hold it. Push the small white button on the Safety Switch down. Release the Measuring Wheel, Did it push the small white button up when it returned to home position ? If not, adjust the Safety Switch Reset Screw or Safety Switch Reset Spring so that it pushes the white button on the Safety Switch up when the Bumper Cup Arm is in home position. You can try re-bending the spring or moving the screw in or out.
If the above procedures fail to restart the machine, you may need to replace the Safety Switch or check the wiring harnesses for any broken wires.
Replacing Safety Switch ("S" or "L")
Tools Required: Soldering Iron/Solder
1. Unplug machine, remove Key Drum & Access Hole Cover. Locate Safety
Switch (see Figure 10 for 555S or Figure 11 for 555 L).
2. Remove wires from old switch with soldering iron.
3. Remove both screws that hold Safety Switch to bracket
4. Screw new Safety Switch onto bracket
5. We find it helpful to cut just a short piece of the wiring off to expose
a new surface before re-soldering wiring to new Safety Switch
Service Figure 10
S Model 6" - 36"
Location of:
Safety Switch
Safety Switch Lever
Safety Switch Spring
Service Figure 10
"L" Model 36"-6"
Location of:
Safety Switch
Safety Switch Lever
Safety Switch Spring
If you can't find the answers here, then please feel free to call us at 1-800-899-9389.
One Source - sales service parts experience
Tigerseal® Products
sales & service
13093 Old Ridge Road
Beaverdam Virginia 23015
Tigerseal® Products is not affiliated with MCM/Phoenix®
Tigerseal® Products is not affiliated with Better Packages® Inc.